Facing the problem of strangled, broken, or malfunctioning headphones? Reconicking the fact that some damages to the earphones demand replacement of certain parts whereas others require complete replacement of one set by another.
The rupturing or splintering of an object does not necessarily mean it needs to be replaced by a new one. The degree may range from dainty to moderate or even worse in some cases.
Fixing of headphones at home will nullify any assurance or commitment of the company for a set time period.
The breakage or damage to the headset's cable may be caused due to continuous exposure to heat or sunlight or maximum pressure to the wires that might suppress the internal cords. The penetration of water inside the wires may also cause a collapse of the set's interior structure.
Fixing Headphone Wires Easily In 2021
Minor damages can be fixed using a tape to connect the ends of the broken wires, whereas weighty defilements require brazing iron and strings to fasten the filaments.
Aerial Mending By Scotch Tape
Fixing headphone wires is effortless and a facile process that does not require the expertise of a person to do so. All you need is a knife, half an inch of cable strand, and tape.
Step 1: Disconnecting the Cords
Primarily, the upper case or the covering of the wires need to be removed during circumstances of mastication by a pet or puncturing ends by squinching between two objects.
Step 2: Insertion of Cable between the Cords
The tiny cable needs to be installed between the separated cords by applying a certain pressure. A certain centripetal force will allow the two strands to separate.
Step 3: Heating the Ends of the Wire
Once the outer sheath has been removed, pluck the ends of the wire inside the coating and unveil them to slight heating until the ends become sticky. The red and green color inside the wires demand special attention. Connecting the opposite color wires will lead to the failure of the entire process.
Step 4: Making a Firm Connection Between Both Ends
Covering the bridged wires with scotch tape will ensure safety and shielding from electric current. The tape insulation will make the headphones protected from any further damage and extend the period of its usage.
Soldering the Wires with a hot iron
Another method underlying the repair of the headphones wire is using scissors and molten iron to mend the piece.
Step 1: Concoction of Wires from Older Cords
Fixing Headphone wires is a simple process, yet a small mistake during its processing can ruin the entire operation. First and foremost, the outer insulation needs to be removed, followed by nicking the wire from the plug area.
Step 2: Tinning the Wires with Hot Iron
Slicing the wire pieces is followed by stroking a hot iron metal piece, called a tin, to melt the wires from the ends. The burnt material residues begin to build near the end and need to be cleaned regularly from time to time.
Step 3: Securing the Ends with a Plug
The coating contains three coloured wires, i.e., red, green, and copper, pertaining to be from left, right, and ground wire, respectively. Each same coloured wire needs to be connected. Otherwise, the connection will not work. Both longer and shorter cords are attached to the plug.
Step 4: Evaluation of the Network Working
Lastly, connect the headphones to a smartphone or a computer to ensure that the sound is clear and the trouble is non-existent at the end. This method is slightly more expensive than the previous one, as it makes use of a plug to be bracketed between the wires.
Use of Multimeter to fix earbuds with multiple wires
There are more than three wires in some headphone sets that need to be installed using a multimeter. Multimeter corrects any headphone issue with a maximum of six wires.
Firstly, the headphone earbuds need to be removed, and the problem in the headphones need to be identified. Noise scraping headphones or built-in microphone headset makes use of more than three wires.
Then, a multimeter is joined to the tapered ends of the headset to pinpoint the correct linkage. In case of failure to understand such a complicated network, expert advice is suggested.
Self-repair: A virtue for the Society
Mending or restoring a thing into its original form by oneself is of benefit for the person and the environment. If a person cobbles a device by himself/herself, he/she is exploiting the resources in the environment to a lesser extent.
Secondly, the dependency on the other person to make alterations or remodelling of an object is not present. The total time required for repair will not exceed more than fifteen to twenty-five minutes.
Wrapping up the discussion, the answer to the question “How to fix the Headphone wires” no longer remains complicated.
Related Guides: Fixing Water Damaged Headphone | Cleaning Your Headphones
FAQs
How do you fix headphone wires at home?
Headphone repair is a simple process. It can be easily repaired at home using scotch tape or a plug. In the case of multiple wires, a multimeter is required.
How do you fix headphone wires with soldering?
Soldering, also known as tinning, requires a hot iron piece bombarded on the wires to melt the ends; once the ends have softened, any alteration can be made to the wire. Most suitably, a plug can be separated between the soldered ends, and the headphones can be restored to their original form.
How do you fix headphone wires without soldering?
If a plug is not available, then twisting the wires from both ends can be performed, followed by removing the outer covering and joining the ends with a tape.
How do you fix earphones when one side doesn't work?
When one side of the headphone stops working, try checking the setting of the device where the headphone is connected. If there is no improvement, inspect the earphone jack and monitor any breakage at that side of the wire where the voice is unclear.
