Do you want to listen to music anytime and everywhere? Your unbelievably tangled headphones create problems in listening to one of your favorite songs. It is the worst thing because every time when you put them in your pocket, they end up turning into this huge mess. It takes a lot of time to fix which makes your mood worse.
How to Untangle Headphone Wires
Sometimes when you unwind the cord, it again turns into a bad Spider-like form. That is why you do not want to deal with these sorts of things anymore and you decide to throw it into the dustbin or decide to buy wireless headphones. However, here are some methods to save your expensive ear-phone wires from wiggling.
Use the Dryer
The mess of the headphone is the middle part. So, always start the untangling of the wire from the mid. Do not try to untangle this thing from the ends. When you get one end of the line then put it underneath something heavy, for example, paperweight, Then stretch the cable. As the wire is stretched from one side to the other side, the knots on it disappear. And then use a hair-dryer to heat up the wire and leave this for up to 24 hours. And after some time the headphones will be straight.
In this approach, place the twisted ear-phones on the palm. Then wrap your three fingers around the wire for creating 8 shape with your index finger and your thumb. Move it around your forefinger towards your pollex. To finish off the figure eight, move the cable back behind the arrow-finger. Then continue this process until all the leads run out.
After that, pinch the wire in the middle of the eighth form to wiggle the wire off of the thumb or pointer finger. At last, take the end of the earpiece and inserting it into the top loop of the eighth frame for the threading of the line. Then leave the end in the circle to finish. With this procedure, your headphone thread will never be tangled again.
Use Crochet to Non-Tangle Earphone
Crochet is basically the yarn that is overlapped on the wire of earphones to prevent the tangling of the wires. They cover the headphone's wires in a simple pattern. To begin, first of all, untwist the cable to create a slip knot for standing single knit. Then insert the hook in the knot. Grab the earpieces and lay them on top of the pin to start yarning from the top of the cord.
After that, keep making the thread until the color of the cord disappears. And once you cover the wire then cut it out. Make sure that you do not cut the wire. To get over the chord, make a chain. Repeat the same action at the other side over the top of the microphone.
You can use spare yarn for coating the line to thicken it up. At last, whenever you roll the earpieces and store them in the lapel area of your jacket, they do not change into the zigzag shape. Moreover, when you are traveling, you can just pull them out and use them immediately instead of having to untangle them.
Untwisting Wire by Pressing
First of all, straighten the intertwisted headphones and this might take a while. Even after straightening the wires, some wrinkles might be left in the line. That is why take a towel and put it on the ground. After that, fold the earpiece between the towel because when you start ironing you do not want to start burning the plastic. While pressing the cable in the towel, hold the other end of it with another hand. Through this, you get straight headphones.
Use the Card
Using stiff paper for unfolding the wires is simple and freeway. You can take a plastic card that can be a hotel card or anything similar to it. The size of the card should be small. The reason for using small size cards is that they can easily carry out small items like handset wires.
It is also best for your pocket perhaps and the size of your headset. In the beginning, unbraid the wires of the handset. Then pull the end of the wire and start winding up on the card. To tie it off, round it the other way. Now you can keep it easy, nice, and tangle-free.
Use Wire Sheath
You waste a lot of hours of your life trying to get your headphones untangled. By the use of cords kinz, you can save your earbuds from more tangling. It is used as a detangler cord protector. The first thing is to detangle the earpiece. Take the disc in one hand and with the help of the other hand put the thread through the cord scan.
Then slide the headphones cable into the notch provided on the disk. Place the thumb on the cable to keep it in place and with the other hand, pull the cord skin through the tunnel. After that, when you unwrap for listening, you will find no more twist in wire.
Use Clip Binder
First, straighten the tangled wires of the headphone. Then open the binder and put the headphones inside it. After that, wind the cable around the clips but do not wrap it too tight. Try to keep it nice. When a little bit of wire is left or reaches the end or near the end, push the headphone jack through the clip. This is a good handy thing and you can use it to restore your handset for the next time.
Related Guide: Fix Loose Headphone Jack | Wearing Headphones with Glasses | Fixing Short in Headphones
There is nothing worse than attempting to unknot headphones to listen from them. These solutions will help you to avoid ever having to deal with tangled headsets. By doing this you can get rid of it. These are affordable tricks that you can use to unwind your headphones so that they do not get tangled in your jacket and purse. And you can take them out and use them without any problem.
Leave a Reply